高级检索

复杂弯曲下刮板输送机形性一体建模与快速求解

Shape-performance integrated modeling and rapid solution for scraper conveyors under complex bending conditions

  • 摘要: 针对当前刮板输送机动力学模型在模拟超长运距、大功率工况时存在的仿真效率低、难以还原复杂弯曲地表真实工况等问题,提出了一种基于多体系统传递矩阵法与虚拟现实技术相结合的刮板输送机形性一体动力学建模及快速求解方法。首先,研究了综采工作面因底板起伏和推移工艺导致的水平及垂直复杂弯曲工况,基于欧拉缰绳理论构建了考虑弯曲角影响的整机弯曲阻力模型;其次,利用多体系统传递矩阵法改进了质量−弹簧−阻尼链传动模型,显著提升了整机动力学模型的求解速度;再次,建立了包含永磁电机驱动系统、液压张紧系统及煤流分布系统的多物理场耦合动力学模型;最后,基于Unity3D开发了能够识别刮板输送机中部槽弯曲角的形状模型,通过MQTT协议将中部槽真实弯曲角及采煤机截割信息传输至MATLAB/Simulink性能模型中,实现了“形”与“性”的跨平台协同仿真。验证结果表明:① 在仿真精度方面,所提方法建立的模型与试验结果对比,其链轮转速最大误差仅为3.64%,与标准建模方法的结果比值波动在0.91,1.08,证明了模型的准确性;② 在仿真效率方面,随着模型的复杂程度增加,所提建模方法的提速优势愈发显著,在实际综采工作面案例中,仿真时间相较于标准方法减少了78.2%,极大提升了模拟效率;③ 案例分析发现,真实弯曲工况会导致机头张力及机头、机尾张力差显著增大,加剧链条疲劳断裂风险;同时,弯曲引起链条速度波动和剧烈振动,导致设备磨损加剧,并增加了机尾张紧系统的控制难度与响应时间。本研究提出的形性一体快速求解方法,不仅能够精准还原复杂工况下刮板输送机的动力学行为,且具备极高的计算效率,为煤矿综采设备的数智化设计、数字孪生构建及智能调控提供了关键的模型基础与技术支撑。

     

    Abstract: A shape-performance integrated dynamic modeling and rapid solution method is proposed based on the transfer matrix method for multibody systems (MSTMM) and virtual reality technology to address low simulation efficiency and the difficulty in restoring real-world complex bending surface conditions in long-distance and high-power scraper conveyors. Horizontal and vertical complex bending conditions caused by floor undulations and pushing processes in fully mechanized mining faces are investigated. An overall bending resistance model considering the influence of bending angles is constructed based on Euler rope theory. The traditional mass-spring-damper chain drive model is improved using MSTMM, and the solution speed of the overall dynamic system is significantly enhanced. A multi-physics coupled dynamic model is established, integrating the permanent magnet synchronous motor (PMSM) drive system, hydraulic tensioning system, and spatio-temporal coal flow distribution system. A shape model capable of identifying the bending angles of middle troughs is developed using Unity3D, and cross-platform collaborative simulation of “shape” and “performance” is achieved by transmitting real-time data via the MQTT protocol to a MATLAB/Simulink performance model. Validation results indicate that a maximum sprocket speed error of only 3.64% is observed compared to experimental data, and the ratio of simulation results to standard modeling results remains within 0.91, 1.08, proving high model fidelity. The speed advantage of the proposed method becomes more pronounced as model complexity increases, with simulation time reduced by 78.2% in actual cases compared to standard methods. Real bending conditions are found to significantly increase head tension and the tension difference between the head and tail, heightening the risk of chain fatigue fracture. Chain speed fluctuations and intense vibrations are induced, leading to intensified equipment wear and increased control difficulty for the tail tensioning system. The dynamic behavior of scraper conveyors under complex conditions is accurately restored while maintaining high computational efficiency. Critical model foundations and technical support are provided for digital design, digital twin construction, and intelligent control of fully mechanized mining equipment.

     

/

返回文章
返回